Automotive hail repair: For dents that are fairly small and not deep, a dent repair kit may be an inexpensive and simple solution. These kits are available at any auto parts store and tend to be very user friendly — instructions are always included. The best part is that they usually cost under $40. Most include several stems for various sized dents, a glue gun and a knockdown tool. You may be surprised at how well the kit works and how professional the result looks. We don’t recommend this kit for large, deep dents — you might cause even more damage trying to fix those with a kit.

First let’s start with some car paint care tricks: Another way to fix the small dents is parking your car in a sunny area. This is an effective way that most of car enthusiasts all know. By doing this way, the metal will heat up and expand. As the car surface expands, the shallow and light dents will pop out. The longer you park your car in a sunny area, the more likely this way will work.

If you want to polish your car and are considering buying a buffer, you can see my simplified approach to car polishing for the true beginner to achieve professional results. As the saying goes, “an ounce of prevention is worth a pound of cure”, and your car is no different. If you are just consistent with the basic instructions I have provided here, your car will not only look fabulous year after year, but will retain much more of its original value when you are ready to sell. Want to save your time and maximize your car detailing efforts. Unless you are a die hard car enthusiast, I actually recommend you find a quality, 100% cloth or hand wash, and take your car there at least every 2 weeks and let the crew there perform the grunt work of car washing.

Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.

Clay: You could also obtain a better finish and a prominent shine if you use good quality clay. Before the clay is applied to the surface, make sure the car is cleaned with paint cleaner. Always remember to use the right applicator pad or a soft terry towel when working on the car’s exterior, to avoid scratching the vehicle. If you don’t know how to use detailing products or clay on your car, view online tutorials and easy do-it-yourself guides to complete the task easily. Read additional info at Auto Decals & Lettering Colorado Springs.

Dents near edges – If a dent of any size is situated near the very edge of a body panel or near a seam, PDR repair may be impossible. The reason for this is that in order to repair a dent using these techniques, you need to access the back side of the dent. The dent has a crease – If there is a sharp crease (like a folded page) in the dent, PDR likely will not work. Older vehicles – If your vehicle is older than 1990 or is a classic car, the odds are good that attempting paintless repair techniques on a dent will damage the paint. This is because the paint quality on older body panels can’t withstand the strain of the repair techniques.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.